Jeep 3.6 Oil Cooler Upgrade

Parts Recommended: Upper and Lower Intake Gaskets – MS97204. I will also supply a couple of picture that include ALL-DATA INFORMATION on torque specs and bolt torquing patterns for the oil cooler adaptor and upper/lower intake. Connect the Oil Temperature and Oil Pressure wiring to the Oil Filter/Cooler Housing.

1. Jeep 3.6 oil cooler upgrade today
2. Jeep 3.6 oil cooler upgrade for jeep grand cherokee 2014 limited 4x4
3. Jeep 3.6 oil cooler upgrade your flash player
4. Jeep cherokee oil cooler
5. Jeep 3.6 oil cooler upgrade lower oil temp

Jeep 3.6 Oil Cooler Upgrade Today

Next, you will want to take the air intake tube off from the throttle body to the air box. A slow leak may not be obvious right after install but hopefully it will leak never again!!! Remove 10mm nuts on the driver side intake bracket located closer to the fire wall. Advance Auto Parts has 1 different Engine Oil Filter Housing for your vehicle, ready for shipping or in-store pick up. Jeep cherokee oil cooler. When it comes to your Jeep Wrangler, you want parts and products from only trusted brands. I removed the 10mm bolt on each side in order to remove the two brackets.

Included for free with this service. I just had yet another oil cooler/filter housing break on my 2014 Rubicon. Be reviving an old thread. Using a T30 Torx driver remove (4) bolts holding fuel rails on the engine. Before removing the upper intake bolts off, you have to remove the heat shielding pad from behind the engine. By adding this item to your cart, the shipping option will not be available for your order. Upper to lower intake bolts – 106 in lbs. Jeep 3.6 oil cooler upgrade for jeep grand cherokee 2014 limited 4x4. New Zealand Dollars (NZ$). The hose is help on by a single clamp that can be removed with pliers.

Jeep 3.6 Oil Cooler Upgrade For Jeep Grand Cherokee 2014 Limited 4X4

INTAKE REMOVALE: First start by removing the two EGR/intake tubes located on the left side (passenger side) of the intake neck. This is a compatible replacement part manufactured by AA Ignition. Atomic: I have an appointment with the dealer to get it fixed, and it's a 100 dollar deductible so it's not a big deal but... Remove Air Box Components (8mm socket or Flat Tip Screwdriver, 10mm socket, 3″ and 6″ extensions) Including one (1) clip on the bottom of the Air Box hose assembly. Could make it a kit to it all at once. Lube the o-rings on the new oil filter/cooler housing for easier assembly. Another 3.6 oil cooler failed. Remove (2) 10mm bolts holding wiring connector on passenger side. South Korean Won (₩). Pull hose and drain. The oil cooler is usually placed near the radiator to maximize cooling airflow.

To maintain the lubricative properties of oil, the oil cooler by cooling the oil (having it flow through it galleries) to the proper temperature range. The bolts will NOT come all the way out from the actual housing. I did not buy OEM intake gaskets. Refer and follow the provided ALL-DATA pages for torque values and patterns during intake reassembly. For installation of the new housing follow the provided ALL-DATA pages for proper torque values and patterns. Jeep 3.6 oil cooler upgrade your flash player. Remove sensor plug and throttle body plug. It has happened, that is why it's brought up. I will post as many photos as I can that will aid you, if you choose to tackle the project yourself. Remove (2) 10mm heater line mounting nuts. I was able to see a little bit of pooled oil looking in between the oil filter housing and the intake.

Jeep 3.6 Oil Cooler Upgrade Your Flash Player

This is common issue on models with these engine as the oil cooler housing was revised in year 2014 from metal to a plastic construction. Year make model part type or part number or question. Pull the Fuel line and tuck away to the right along with the wires from the injectors and coils. Once the contents are out go ahead and reattached the hose and clamp. ALL THE PARTS YOUR CAR WILL EVER NEED. Your cart will be set to In-Store Pickup. My Temp sensor broke inside old housing and pressure sensor seems to be a common item that goes out. Once pulled, you can then remove the clam and coolant hose off. Engine Oil Cooler and Filter Housing Adapter Kit - Replaces 68105583AF, 68105583AE - Fits 3. Another oil cooler bites the dust. Carefully pull the blue safety clip from the fuel line and you should be able to squeeze the white clip. Without regular oil changes, the cooler may fail at 50, 000 miles and need to be replaced.

If you prefer to shop in person for the right Engine Oil Filter Housing products for your Wrangler, visit one of our local Advance Auto Parts locations and you'll be back on the road in no time! Remove foam from behind the upper intake at firewall. Some manipulation of the housing is required to get it back into the mounts. 3.6 Oil Filter / Cooler Housing. It is what i would use when the day happens, no question. After driving your JK for a good period of time, I would check for any new leaks. Swedish Krona (SEK). Unplug the fuel injectors on the passenger side and remove the fuel injectors on the driver side.

Jeep Cherokee Oil Cooler

You will have the intake off long enough to have the open ports be a hazard. Prices may vary depending on your location. 11 Oil Coolers found. Maybe a mod here can delete it. Remove (2) clips on rear of the upper intake on the passenger side. You will then have to remove the front two 10mm bolts below the throttle body in the front.

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Mechanic comes to you. This is an older thread, you may not receive a response, and could. Install new oil filter/cooler housing.

Jeep 3.6 Oil Cooler Upgrade Lower Oil Temp

6L V6 Chrysler 200, Town & Country, Dodge Grand Caravan, Jeep Grand Cherokee, Wrangler, Ram 1500, 2500. You will be able to see the general area (top transmission bell housing and behind the engine). Don't forget to replace and check all fluids prior to starting vehicle. Norwegian Krone (NOK). If you want to confirm the leak before you buy parts or disassemble anything, you should be able to get a camera snake into the engine valley through the front or back of the engine.

Include vehicles sold in Mexico.