Street Faction Engineering Rear Seat Delete
Scope of delivery: – Clubsport strut bar. The sizes of the nuts and bolts we give may be different from what you have, so be prepared with different size sockets and wrenches. Uses existing rear trunk liner. Interior trim pieces in MINI R56 cars are often made of preformed hard plastic. Rear seat delete mini cooper 2. Here is the finished RSD. I had removed the rear seats to make more room for cargo, but this leaves two awkward dips in the cargo area. Vehicle models change and evolve, as they grow older, so the vehicle shown in our illustrations may vary slightly from yours. The delete comes wrapped in our black carpet. I sprayed the headliner glue on the top half of the board. If you want a better fit, start with a 44" x 24" board. All deletes are built to order, please refer to our homepage for our current lead time.
- Rear seat delete mini cooper 2
- 2004 mini cooper s rear seat delete
- Rear seat delete mini cooper transmission
- Rear seat delete mini cooperative
Rear Seat Delete Mini Cooper 2
Parts Required: Seats, seat parts. For the area created by expanding the rear seat bench, we also offer a custom-fit clubsport carpet, which is also made by hand. Cut four pieces from the other 1 1/4" strip. Once triggered the device cinches up the seat belt by 55 mm (about 2 inches). Note: - Designed to delete seats, not to be used as seats. Recycle parts, packaging and fluids when possible. Stern Performance Rear Seat Delete Kit - Mini R56. If you're working with the electrical system, disconnect the battery before beginning. The Clubsport strut is made of powder-coated aluminum, in the color of your choice. Performance Gain: Access to seat switches and components beneath seats.
2004 Mini Cooper S Rear Seat Delete
Of course, the set has been specially developed for your vehicle and we guarantee a 100 percent accuracy of fit. Therefore, our rear seat delete products cannot be exchanged and we cannot accept cancellations, changes or returns. 2004 mini cooper s rear seat delete. It is designed to fasten to OEM mounting points using the supplied hardware. Use scrap pieces of wood and clamps to press the fabric until it is dry. These are general lead times and can be increased if the manufacturer encounters supply chain disruption, or other production delays. Next, drape the flannel over the board. If you aim to remove either front seat, disconnect the negative battery terminal and insulate the end to prevent accidental reconnection.
Rear Seat Delete Mini Cooper Transmission
Use clips to hold the fabric in place over the rear edge. The Clubsport Set is plug & play and replaces the rear seat bench with a strut and a net, which is attached using a bracket. Two pieces are 2 5/8" long. This serves the purpose of weight reduction and is a real eye-catcher. I had a spare piece of pegboard and decided to use it to make a cover, also known as a rear seat delete kit. Make triangle-shape cuts to the sides for proper width. Rear seat delete mini cooperative. Miniacal - Greg's 2007 Mini Cooper S. DIY Rear Seat Delete.
Rear Seat Delete Mini Cooperative
⚠️CALIFORNIA WARNING: Cancer and Reproductive Harm -. Keep in mind that when your car was serviced before, parts may have been replaced with different size fasteners used in the replacement. Leave a comment below. The blue metal loop is where the seat was attached.
Do not work on your vehicle if you feel the task is beyond your ability. The unfinished wood soaks up a lot of glue, so I had to spray a lot. Plastic clips or metal screws may be used to hold them in place. Then turn the board over. Multiple options are available to allow you to pick a combination that will best suit your needs. There should be a few inches of excess around the edges. The pyrotechnic device has an explosive charge, which is triggered by the airbag (MRS) control module in case of sudden deceleration such as a car crash. The assembly points for the net can be seen in the product images. While we make every effort possible to keep our customers informed of delays, if we do not receive updates from the manufacturer we cannot in turn update our customer. It now fits into the nook formed by the wood blocks, and keeps the board from moving. If something seems different, let us know and share your info to help other users. Enjuku Racing does not manufacture these products nor have ANY control over the manufacturers production timelines and is in NO WAY responsible either financially or otherwise for compensation for increased lead times because of manufacturer delays.
Copyright © 2008, Greg Watanabe. Loctite Stik'n Seal glue. Purposes: - Firewall for track vehicles running a rear fuel cell. They create a nook which the metal loop slides into, as shown in the fifth photo below. It might be better to use speaker box carpet, rather than flannel, but I didn't find speaker box carpet at the local fabric store. Special features of custom-made products (strut bar, net, carpet). 3' x 4' black flannel. Protect your eyes, hands and body from fluids, dust and debris while working on your vehicle. To prevent cargo from sliding forward and hitting the seats when I brake, I attached a 3/4" strip of wood to the front edge of the pegboard. The pyrotechnic pre-tensioner in the seat belt buckle mechanism poses a hazard if not handled carefully. Legal only for use in competition vehicles which may never be registered, licensed, and/or used on public streets or highways; and also for use in other exempted vehicles. When leaving a comment, please leave your vehicle information.
Glue them to the pegboard as shown below. Production time: Up to 4 weeks. Once removed, you can repair items like the seat belt buckle, or in the rear, the fuel pump or seat belt buckles. Wait a few minutes for the top to dry. Pre-Orders: Once we get at least 5 pre-orders made for each chassis, we will bring in a local car for R&D. Braced underneath to hold up to 150 pounds distributed evenly. Do you have questions or want to add to the article? Unfortunately we cannot make exceptions. Made of lightweight 1/4" plywood. Glue it in place and clamp it until dry. This process can take anywhere between 4-8 weeks depending on our workload. The clubsport net is available in several colors and the seam color can be specified in the order comment. I didn't want to try to glue the entire surface at once, so I did half at a time.